› Bulk Ti and Ti6Al4V through Consolidation of Chips by Severe Plastic Deformation Methods - KEYNOTE: Michael Zehetbauer, University of Vienna, Faculty of Physics, Wien, Austria
10:10-10:30 (20min)
› Micromechanical behavior of multilayered Ti/Nb composites revealed by high-energy diffraction techniques - Nan Jia, Northeastern University
10:30-10:50 (20min)
› Strengthening and toughening mechanisms of a GNS/Mg composite with layered structure - INVITED: Xiaojun Wang, Harbin Institute of Technology - Yeyang Xiang, Harbin Institute of Technology - Hailong Shi, Harbin Institute of Technology
11:20-11:40 (20min)
› The formability AA1050/AA7050 Al multilayered sheets produced by Accumulative Roll Bonding (ARB) in traditional drawing and in single point incremental forming (IF) processes - Andrea Kliauga, Universidade Federal de Sao Carlos - UFSCar
11:40-12:00 (20min)
› Hierarchy of the macrozone features in Ti-6Al-4V alloy inferred from massive FFT-based polycrystal plasticity calculations - INVITED: Stephane BERBENNI, LEM3 UMR 7239 Université de Lorraine, CNRS, Arts et Metiers ParisTech, France
14:30-14:50 (20min)
› Numerical assessment of substructure evolution and kinetics of recrystallization in aluminum alloys - Jurij SIDOR, Savaria Institute of Technology, Faculty of Informatics, ELTE Eötvös Loránd University
14:50-15:10 (20min)
› Grain growth in thin films – when the third dimension matters - KEYNOTE: Dana Zöllner, Otto-von-Guericke-University Magdeburg, Faculty of Natural Sciences, Universitätsplatz 2, 39106 Magdeburg
09:40-10:00 (20min)
› Laser powder bed fusion of Fe–Co–Ni–Cu high-entropy alloys guided by computational simulation - Asker Jarlöv, School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore Institute of Manufacturing Technology (SIMTech), Agency for Science, Technology and Research (A*STAR)
10:00-10:20 (20min)
› Improving Piezoelectric Properties of ZnO Thin Films Deposited via AP-SALD with Texture Enhancement - Hayri Okcu, Doctoral Candidate
10:20-10:40 (20min)
9:40 - 10:20 (40min)
Deformation textures
Room 4
10:20 - 10:40 (20min)
High Entropy Alloys
Room 4
› Annealing behavior of a carbon-doped nanocrystalline CoCrFeMnNi alloy - Yulia Ivanisenko, Institute of Nanotechnology, Karlsruhe Institute of Technology (KIT)
10:20-10:40 (20min)
› Novel insights on the micro-texture formation in additive manufacturing of Ti-6Al-4V alloy - INVITED: Shibayan Roy, Indian Institute of Technology Kharagpur
11:10-11:30 (20min)
11:10 - 12:10 (1h)
High Entropy Alloys
Room 4
› Microstructure evolution during hot deformation of newly developed 30Nb5Ta30Ti15V20Zr high entropy alloy - INVITED: PRAMOTE THIRATHIPVIWAT, Yokohama National University
11:10-11:30 (20min)
› Investigation of the microstructural evolution and mechanical properties of diffusion welded equiatomic CoCrFeMnNi-based multi-component alloys to 316L stainless steel - Olushola Bamidele Nenuwa, Ecole Nationale Supérieure des Arts et Metiers Metz, Department of Mineral and Petroleum Resources Engineering, Federal Polytechnic, P.M.B. 5351, Ado-Ekiti, Nigeria
11:30-11:50 (20min)
› Microstructural evolution, texture and mechanical properties of cold-rolled CoCrFeNi medium-entropy alloy during different annealing treatments - Konstantin V. Werner, Department of Civil and Mechanical Engineering, Technical University of Denmark
11:50-12:10 (20min)
12:10 - 12:50 (40min)
Grain boundary
Room 3
12:10 - 12:50 (40min)
Phase transformations
Room 4
› A study on microstructure and mechanical properties of Co66.66Cr16.67V16.67 metastable medium-entropy alloy - LUDA WANG, Northeastern University [Shenyang], University of Lorraine;LEM3
12:10-12:30 (20min)
› Martensitic transformation and magnetostrictive effect of textured MnCoSi-based alloys - Bo YANG, Northeastern University [Shenyang]
12:30-12:50 (20min)